Ltd., a 100 subsidiary of Canon Singapore Pvt. Alarm Panel HardwareFirmware Release Letter BVIP Firmware 5.52Canon India Pvt. All firmware versions of the GV2/GV3 Series Control Panels and the FPD-7024 will work with the DX4020. Bosch Security Systems, Inc Technical Support Alarm Panel Configuration Alarm Panel Firmware The firmware in the G Series Control Panels must be version 6.3 or later to work with the DX4020.
Select the drop-down arrow beside Save and click on Safe as. Click on the current version of RPS to start the download. Set up in 1997, Canon markets over 200.- Select the tab: Software Downloads 3.
To Cross-Domain Solutions from Bosch. OnePlus 7 Pro (guacamole) - Pixel Experience> - July security patch - Updated translations.Using Intelligent Tracking Displaying the Compass Heading Firmware Enhancements Defects Resolved Known Limitations and RestrictionsIn addition to providing outstanding products, we utilize expertise in sensor technology, systems integration, software and services, as well as our own IoT cloud, to offer each customer connected, cross-domain solutions from a single source. 6.OnePlus Broken Screen Data Recovery Software Solutions. Disable any Anti-Virus or Firewall software (this is very important).
Introduction 1.1 Disclaimer of Warranty Bosch Security Systems, Inc. We reserve all rights of disposal such as copying and passing on to third parties.Firmware Release Letter 1. LAW IS PROHIBITED.© Robert Bosch GmbH reserves all rights even in the event of industrial property rights. DIVERSION OF THE SOFTWARE CONTRARY TO U.S.
4.1 Using Intelligent Tracking The VG5-836-ECEV and the VG5 700 Series HD PTZ cameras with BVIP Firmware 5.52 utilize the builtin Intelligent Video Analytics (IVA) to continuously follow an individual or an object. Software Changes This section identifies enhancements and defect resolutions provided in BVIP firmware version 5.52. About This Service Pack Release This is an Engineering Release of the firmware components identified section 1.3.4. 1.3 Scope This document describes the BVIP Firmware which includes the following components: ComponentAutoDome 800 AutoDome Junior PTZ HD AutoDome Junior Fixed HDAutoDome 700 AutoDome Easy II IP AutoDome VG4 Series IP2. It also documents component compatibility, workarounds, and any feature restrictions.
Intelligent Tracking remains in the IDLE state while the camera is moving due to a user action (for example, initiating AutoPan). If the last userselected mode for Intelligent Tracking is Click, and a user issues the AUX 78 OFF command to deactivate Intelligent Tracking, all subsequent AUX 78 ON commands will activate Intelligent Tracking in the Click mode. When the AUX 78 ON/OFF command is issued to activate/deactivate Intelligent Tracking, The AUX 78 ON command selects last known Intelligent Tracking mode (either Auto or Click). Note: Intelligent Tracking is not available on the following models: Intelligent Tracking controls the pan/tilt/zoom actions of the camera to keep the selected object in the scene.
Once Intelligent Tracking loses a tracked target and enters the IDLE state, Intelligent Tracking will not react to any other motion in the field of view. Support for the Click feature is planned for the BVC 1.4 release. BVC 1.3.837 does not support the Intelligent Tracking Click mode. The Click mode works only on the Livepage view. When switching between the Auto and Click modes, allow for a transition time as the camera switches algorithms.
Motion is then lost and Intelligent Tracking enters the IDLE state. While in the ACTIVE state Intelligent Tracking may suddenly divert to the opposite direction of the tracked motion (the motion track appears to take the shape of a small hook). Intermittent loss of tracking has been observed. The camera may remain in place for extended periods of time (hours have been observed) until some other event occurs. The camera appears to be fixed in place. While the camera is in active Night Mode, Intelligent Tracking exhibits a “hang” after motion is lost.
Note: The compass feature is not compatible with Bosch Intelligent Tracking. The AutoDome displays the cardinal or intercardinal (N, NE, E, SE, S, SW, W, NW) heading in which the camera is pointing. We reserve all rights of disposal such as copying and passing on to third parties.4.2 Displaying the Compass Heading The VG5 700 and 800 Series AutoDome allows a user to display the compass heading of the camera in the lower-right corner of the image display. © Robert Bosch GmbH reserves all rights even in the event of industrial property rights.
Determine the North compass heading, and then move the camera to that position. To set the North calibration point: 1. The AutoDome then displays the compass heading based on the number of degrees from the North calibration point. The AutoDome uses this calibration, usually set to magnetic North, as the zero degree pan position and as the North compass heading. You must first calibrate the AutoDome to North before the camera displays accurate compass headings. Once Intelligent Tracking is deactivated, the camera returns the compass heading to the display.
Change RequestIMC00004077 IMC00003833 IMC00004215 IMC00004285 IMC00004323Description Added Intelligent Tracking capability to VG5 800 Series cameras. 4.3 Firmware Enhancements The following ENHANCEMENTS have been resolved for this delivery. Click the On radio button for the Compass parameter.
VG5 700: Implemented low light noise suppression. Added support for 99 presets for camera control via ONVIF. Compass feature added to VG5 700 and to VG5 800 Series cameras. Sharpness defaults changed for VG5 700 series cameras (36x: 8, 26x: 6). Improved sharpness and noise reduction performance. Provided support for 24 privacy masks for all AutoDome series cameras.
Blanked sectors no longer cause a false alarm while Bosch Intelligent Tracking is active. Improved recorder tour performance so manual interactions do not break preset functionality. Change Request IMC0000418 IMC00003955 IMC00003131 IMC00004041 IMC00004195Description Corrected performance to prevent Autopan from losing field of view when returning from Inactivity.
Bosch Security Us Firmware Upgrade The AutoDome
O The camera is actively tracking an object using Bosch Intelligent Tracking. O The Trajectory parameter is set to On. An issue with Video SDK version 5.4 (a component of BVIP firmware version 5.52) may cause Internet Explorer to crash under the following set of conditions (all conditions must be met): o Internet Explorer shows the Livepage view for an AutoDome camera running BVIP 5.52. If you are updating an IP-enabled AutoDome Series camera that is currently running BVIP Firmware 4.53 or earlier, you must first upgrade the AutoDome to BVIP Firmware 4.54 before installing BVIP Firmware 5.52. Improved the rate for updating sector titles.
0 kommentar(er)
